Shure 565SD Bedienungsanleitung PDF herunterladen

Model 565SD User Guide

C3060 (Rev. 7)

Printed in U.S.A.

GENERAL

The UNISPHERE I 565 Series microphones are dual-imped-

ance, unidirectional dynamic microphones with a strong,

wire-mesh, spherical front grille that contains a highly effective

wind and “pop“ filter.

Shipped connected for low-impedance operation, 565 Series

microphones provide excellent vocal or speech reproduction on

lecterns and stages, and are a popular choice for use in public au-

ditoriums, churches, convention halls, and schools.

FEATURES

• Selectable dual impedance operation

• Silent magnetic reed on/off switch with lock-on option

• Cardioid dynamic

• Frequency response: 50 to 15,000 Hz

MODEL VARIATIONS

Model 565SD-CN: Supplied with 6.1 m (20 ft) XLR cable.

Model 565SD-LC: No cable supplied.

CONNECTIONS

When using the microphone with a balanced input, pins 2 and 3

are the audio signal carriers. When using the microphone with an

unbalanced input, use a cable wired with pin 2 as the signal carrier

and pin 3 connected to the cable shield (ground), such as the

Shure C20HZ high-impedance cable.

IMPEDANCE SELECTION

The microphone is shipped connected for low impedance oper-

ation. To change to high impedance, proceed as follows (refer to

Figure 1):

1. Remove plug element at receptacle end of microphone by

turning slotted setscrew in (counterclockwise) and carefully

withdrawing plug element from case.

2. Disconnect 2-terminal impedance selection socket from rear

of plug element.

3. Reconnect 2-terminal impedance selection socket in reverse

position so that pin 3 of plug element is inserted in socket ter-

minal “H” (White).

4. Reassemble plug element into microphone and seal setscrew

securely by turning out (clockwise).

IMPEDANCE SELECTION-

RECEPTACLE END OF MICROPHONE

FIGURE 1

POLARITY

All cables and microphones should be tested to ensure that they

have the same polarity. To test two microphones and/or their ca-

bles for proper polarity, connect them to an amplifier and talk or

sing into them while holding them three or four inches apart. The

sound from the speakers should be the same when talking into ei-

ther microphone or directly between them. If the sound drops dras-

tically, or if a dead spot is found when talking between the two

microphones, either the microphones or their cables have opposite

polarity.

To change the polarity of a microphone cable, either use a

Shure A15PRS phase reverser or interchange the wires connected

to pins 2 and 3 of the three-pin connector at one end of the cable.

To change the polarity of a microphone, the microphone cartridge

leads must be interchanged. This should be performed by your

dealer, the Shure Factory Service Department, or other qualified

service personnel.

SPECIFICATIONS

Type

Dynamic

Frequency Response

50 to 15,000 Hz

SET SCREW

IMPEDANCE

SELECTION SOCKET

PLUG

ELEMENT

PIN 3

20 200001000 1000050 100

9876543298765432

+10

–10

-20

+20

1 2 3 4 5 6 ... 11 12

Inhaltsverzeichnis

Seite 1 - Model 565SD User Guide

Seite 2 - REPLACEMENT PARTS

10Livello di uscita (a 1.000 Hz) *0 dB = 1 volt a pascal (1 Pa = 94 dB SPL)PolaritàUna pressione sonora positiva sul diaframma produce una ten-sione p

Seite 3

Seite 4 - ACCESSOIRES EN OPTION

SHURE Incorporated http://www.shure.comUnited States, Canada, Latin America, Caribbean:5800 W. Touhy Avenue, Niles, IL 60714-4608, U.S.A.Phone: 847-6

Seite 5 - STECKELEMENT

2Polar PatternCardioid (unidirectional)-uniform with frequency, symmetricalabout axislmpedanceDual. Microphone rating impedance is 150 ohms (250 ohms

Seite 6 - KONSTRUKTIONSDATEN

3GÉNÉRALITÉSLes UNISPHERE I série 565 sont des microphones électrody-namiques unidirectionnels à double impédance, munis d'un grille sphérique ré

Seite 7

4Niveau de sortie (à 1 kHz) *0 dB = 1 volt par Pascal (1 Pa = 94 dB NPA)PolaritéUne pression acoustique positive sur le diaphragme produit unetension

Seite 8 - ACCESORIOS OPCIONALES

5ALLGEMEINESDie Mikrofone der Serie UNISPHERE I 565 sind dynamische Doppelimpedanz-Richtmikrofone mit einem robusten vorderen Drahtgaze-Kugelgrill, de

Seite 9 - PIEDINO 3

6lmpedanzDie Nennimpedanz des Doppelimpedanzmikrofons beträgt 150Ohm (Istwert: 250 Ohm) beim Anschluß an Mikrofoneingängemit Nennimpedanzen von 19 bis

Seite 10 - SPECIFICHE DI PROGETTAZIONE

7GENERALIDADESLos UNISPHERE I serie 565 son micrófonos dinámicos unidi-reccionales de impedancia doble con una rejilla esférica de malla de alambre qu

Seite 11

8Nivel de salida (a 1000 Hz) *0 dB = 1 voltio por Pascal (1 Pa = 94 dB SPL)PolaridadUna presión positiva en el diafragma del micrófono produce unvolta

Seite 12

9DESCRIZIONE GENERALEI modelli UNISPHERE I serie 565 sono microfoni dinamici, uni-direzionali, a doppia impedenza, dotati di una robusta griglia ante-